www.deadharddrive.com

Chris · Officially active! Joined: 27 Jun 2010 Posts: 2

I have a hard drive that was an external that someone plugged the wrong voltage power brick into. Causing the logic board to blow. in an attempt to recover. I need to find it's replacement. I am willing to pay for the Harddrive and toss you a bit of dollars your way as well as the data is VERY important and I dont have THAT MUCH to send to data recovery. ($1,000 +)

Specs:

Size: 1 Terabyte

SN: WD10EAVS-00D7B1
WWN:50014EE257B3AA74
DCM: DHNNNT2CFB
LBA: 1953525168
Sata / 8 MB cache
5 VDC: 0.70A
12 VDC: 0.55A
R/N: 701590

WDT-701590(B)

NMB-003 Class B

Any more details I can give on my work break. hope someone has one I can buy.

fzabkar · Deadharddrive regular +3 Joined: 02 Apr 2010 Posts: 210

If you upload a detailed photo of the component side of your board, one of us may be able to help you repair it. Many times the problem is only a shorted diode, in which case it can simply be removed.

Good luck.

harddrivespecialist · Posted: Tue Jun 29, 2010 2:29 pm Post subject: Help with your WD drive.

Hi!

I have a board for your Western Digital drive.
_________________
www.datarecoveryne.com

sunnydreamspace · Deadharddrive regular +5 Joined: 04 Jan 2009 Posts: 540

hi,
i have PCB fix for you need and can help you program transfer original FW. please feel free to contact me by email or MSN if need.
BTW, Reference here:http://www.deadharddrive.com/forums/viewtopic.php?t=6231
_________________
provide Hard drive PCB,entire drive/ Data Recovery service.... big HDD resource. talk to me immediately! sunnydreamspace@hotmail.com
skype: sunnydreamspace

Eric Lee · Posted: Wed Jun 30, 2010 2:47 am Post subject:

Hi,

If you need the working PCB, we have it.

Thanks
Eric
_________________
HK MingDi electronics Co., Ltd. http://www.hkmingdi.com/enindex.asp
MSN/E-mail：eric_lee8341@hotmail.com
Specialize in HDD PCB!!! Real in stock!!
Skype：eric.lee1984

Chris · Officially active! Joined: 27 Jun 2010 Posts: 2

Hey guys. Thanks for the help. I usually check this every few days. anyway.

I dont have a screwdriver / torx screwdriver to pull the Logic board off. i'll have to goto Microcenter (Computer store) for one I guess.

Anyway, so all I need to do is post a pic of the logic board for comparison purposes?

Also, whats this about transferring firmware? Wouldn't the logic board be replaced with the newer one then connected to the hard-drive itself?

side note. It did smoke on me (the sata power section) when hooked to the computer. I doubt the harddrive itself is dead. just the logic board.

harddrivespecialist
sunnydreamspace
Eric Lee

How much do you charge and are you reliable ?

sunnydreamspace · Deadharddrive regular +5 Joined: 04 Jan 2009 Posts: 540

hi,
check the diode on PCB which near SATA connector. and you can feel free to contact me for get the reference pic for the PCB part which often get fails. [/img]
_________________
provide Hard drive PCB,entire drive/ Data Recovery service.... big HDD resource. talk to me immediately! sunnydreamspace@hotmail.com
skype: sunnydreamspace

fzabkar · Deadharddrive regular +3 Joined: 02 Apr 2010 Posts: 210

[quote="Chris"]Also, whats this about transferring firmware?[/quote]
Depending on the model, there may be a serial EEPROM chip which contains unique drive specific calibration data. You need to transfer these data from patient to donor. A photo would be useful ...