www.deadharddrive.com

mccorkled · Deadharddrive regular Joined: 12 Aug 2009 Posts: 15

I have this hard drive that has everything I have ever done on it. Code, Animation, Old family pictures... etc. I plugged the wrong power cable into it for my external drive and fried the board. Its been over a year and the longer it sits the harder it will be to get a replacement. What should I do? Can you help me? I already bought 2 boards that were $50 EACH and neither one works.

sunnydreamspace · Deadharddrive regular +5 Joined: 04 Jan 2009 Posts: 540

hi,
i can help. please send images of all your PCB to me by email. and mark which one is original. i would like to help. thanks.
_________________
provide Hard drive PCB,entire drive/ Data Recovery service.... big HDD resource. talk to me immediately! sunnydreamspace@hotmail.com
skype: sunnydreamspace

Eric Lee · Posted: Thu Aug 13, 2009 3:00 am Post subject:

You could send me the pic too, I could also help.

Thanks
Eric
_________________
HK MingDi electronics Co., Ltd. http://www.hkmingdi.com/enindex.asp
MSN/E-mail：eric_lee8341@hotmail.com
Specialize in HDD PCB!!! Real in stock!!
Skype：eric.lee1984

mccorkled · Deadharddrive regular Joined: 12 Aug 2009 Posts: 15

Thank you all so much for your replies. I email the websites owner ages ago. I just receive an email today with a link directing me to this forum! Thanks again for returning my email.

I will post pictures in the morning. I am a bit confused on which board is which but I think the original burnt board is back on the HDD because I didnt want to lose it. I need to get a torx to take the board off.

thanks again!

hddmania · Posted: Thu Aug 13, 2009 2:11 pm Post subject: I sent you a PM

Hey, I sent you a PM.

mccorkled · Deadharddrive regular Joined: 12 Aug 2009 Posts: 15

Let me know if this works for you

mccorkled · Deadharddrive regular Joined: 12 Aug 2009 Posts: 15

I would be more then happy to trade someone for the board I need. You can have BOTH of the other working boards I've tried.

sunnydreamspace · Deadharddrive regular +5 Joined: 04 Jan 2009 Posts: 540

hi,
i have these model of PCB. but i will need to know the full model of your. please check the model on second image left-down corner. it type 2060-001092-XXX REV:X. please send this detail to my email. thanks.
_________________
provide Hard drive PCB,entire drive/ Data Recovery service.... big HDD resource. talk to me immediately! sunnydreamspace@hotmail.com
skype: sunnydreamspace

Eric Lee · Posted: Sat Aug 15, 2009 3:11 am Post subject:

If you have working PCB in your hand right now, you need to match the exactly PCB No. which was printed in the back side of your PCB and have some words "REV".

And then you need to do rom swap before your swap PCB.

That's all.
Thanks
_________________
HK MingDi electronics Co., Ltd. http://www.hkmingdi.com/enindex.asp
MSN/E-mail：eric_lee8341@hotmail.com
Specialize in HDD PCB!!! Real in stock!!
Skype：eric.lee1984

mccorkled · Deadharddrive regular Joined: 12 Aug 2009 Posts: 15

If thats the case then I can probably use the PCB I have now. I dont know how to do a rom swap though.

To the poster above that: I sent it to your email

mccorkled · Deadharddrive regular Joined: 12 Aug 2009 Posts: 15

I wish people would stop trying to sell boards to me. I already bought 2 guaranteed to work! Neither did. Im not buying another. If someone sends me one I can send you money after I verify it works... OR I will send you both of the other 2 boards.

hddmania · Posted: Tue Aug 18, 2009 4:12 am Post subject:

I'm sure the PCB you purchased are working PCB, you have to get the adaptive info transfered, or you may have more damages than just the PCB...

Go buy the PCB with reprogramming service as a set. Or go with the one that you have to send the drive in to reprogram or to recover your data, then they will not sell you the PCB if the proble was something else....

If your data was available, they'll send you the list or to show you what they reocvered and if you need the data, then you'll pay them....

mccorkled · Deadharddrive regular Joined: 12 Aug 2009 Posts: 15

Well the board I bought makes the drive spin up so Im sure it will work. I need to know how to reprogram the board though. If anyone is interested in trading some money plus the 2 working boards thats great. One person here said they have the exact board I need in stock. The problem is its over $80 and I spent well over $100 already on boards that were promissed to work

mccorkled · Deadharddrive regular Joined: 12 Aug 2009 Posts: 15

anyone willing to help me out? I refuse to give someone I don't know and who has less then like 1000 posts, $80 or more of my hard earned money.

harddrivespecialist · Posted: Sun Aug 23, 2009 6:24 pm Post subject: